If you can smell gas: turn the gas off at the cylinder, open doors and windows, don't use switches or naked flames, and get out. If there's any risk of fire or someone feels unwell, call 999. Never try to adjust a gas burner yourself.
What it means
The heater tried to light or keep burning on gas but the gas didn't arrive properly, so it shut itself down to stay safe. It's the most common Truma code on newer heaters, and nine times out of ten it's simply the gas supply.
What you can check yourself
- If you can smell gas at any point: turn the cylinder off, open doors and windows, don't use switches or flames, get everyone out and call a Gas Safe engineer.
- Check the gas cylinder isn't empty and its valve is fully open; swap to a full cylinder if in doubt.
- Check the gas tap for the heater inside the van (usually in a kitchen drawer or cupboard) is open.
- Light a hob burner – if that won't light either, the problem is the supply, not the heater.
- If your regulator is a Truma MonoControl CS with a crash sensor, a hard jolt can trip it; with no smell of gas, press its yellow reset button.
- Acknowledge the code on the panel and try again; in very cold weather use propane rather than butane.
Likely causes
- Empty cylinder or a closed cylinder valve or gas tap
- Crash-sensor regulator tripped
- Butane that won't vaporise in the cold, or an iced-up regulator
- Wrong or faulty gas pressure from the regulator
When to call a pro
If the gas supply is good (the hob lights fine) and E 517 H keeps coming back, get a Truma service agent or Gas Safe-registered engineer to check the gas pressure and the heater's burner.
Good to know about Truma Combi heaters (gas, E and D)
- W means a warning: the heater carries on as best it can and the warning clears itself once things are back in range. E means a fault: the heater stops. The H on the end just means 'heater'.
- On a CP plus panel, turn the knob to the warning triangle and press it to read the code. Fix the cause, then press the knob again to clear it.
- Reset more than four times in 15 minutes and the heater blocks itself for 15 minutes (E 607 H). Stop, find the cause, then try once.
- There are two generations of codes. Older Combis show two- or three-digit codes (E 112 H, W 24 H); newer ones show 400-600 series codes (E 517 H, W 401 H). Some numbers are described slightly differently between the two, so treat the meaning as a strong pointer rather than gospel.
Understand the part
Other Truma codes
E 43 HVoltage too highE 44 HBattery too low – heater has stoppedE 112 HFlame not detected – usually no gas reaching the heaterE 121 HGas valve closed or flame unstableE 122 HFlue or air intake blocked (older gas heaters)E 202 HGas not getting through – flame failureE 211 HGas valve closed or flame unstableE 212 HFlue or air intake blocked (or no gas)E 507 HGas supply interrupted while runningE 607 HToo many resets – heater blocked for 15 minutesE 621 HRoom temperature sensor faultE 632 HElectric overheat protection trippedW 17 HHot water mode with an empty water heaterW 18 HWarm air can't get out – heater overheatingW 24 HBattery getting low – heater may stop soonW 42 HWindow open above the flueW 45 HNo mains (230-volt) power to the heaterW 255 HHeater has no 12-volt power or has lost contact with the panelW 401 HHot water mode with an empty water heater (newer heaters)W 402 HAir overheating (newer heaters)W 408 HGas dropped out in mixed (gas plus electric) modeE 122 HDiesel heater out of fuelE 131 HDiesel heater lost contact with the panel
Checked against: Copy of the manufacturer's manual. Last reviewed October 2026. General guidance only, not a diagnosis.
